Difference between revisions of "TIAO Smart Sprinkler Pi Controller User Manual"

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!

Revision as of 11:04, 10 October 2014

TIAO Smart Sprinkler Pi

For system connection diagram, please refer to TIAO Smart Sprinkler Pi System Connection Diagram. For hardware layout, please refer to TIAO Smart Sprinkler Pi Hardware Layout.

The TIAO Smart Sprinkler Pi (TSSPi) is a piece of hardware controls your irrigation systems. It replaces your traditional sprinkler controller. TSSPi has many benefits over the traditional sprinkler controller:

TSSPi Controller Software Features

• Easy setup - no monitor nor keyboard required for raspberry pi, only a network cable or USB wifi adapter
• Web interface - program the watering schedule using your PC or mobile phone
• Supports complicate watering schedules
• Unlimited watering schedules
• Allow seasonal adjustments
• Weather API access - automatically adjust watering amount/time by checking online weather forecast (rain/wind etc)
• Control your sprinkler stations from anywhere in the world
• Software supports unlimited stations
• Controls 1 to 16 stations(or 1 master station + 15 stations)
• Supports rain sensor
• Open source software - which means you can add your own function to the controller!
• System ON/OFF hardware switch
• Status LEDs (power, Pi power, system on, system running)
• Tap start/stop - simply tap on the screen to start or stop the stations
• Recommended browser - Google Chrome

Installation

The TSSPi controller software is pre-installed in our Raspberry Pi SD image, you can download it from here.

The image compressed in 7Z format, you can uncompress it by using 7Zip or peaZip.

After you have uncompressed it, follow the instructions from http://www.raspberrypi.org/documentation/installation/installing-images/ to load the images on the SD card.

Hardware connection

Your raspberry Pi is getting power from TSSPi, so no separate power needed for Pi. The required connection to your Pi is a network cable or a supported USB wifi adapter. For sprinkler connections, please follow this page: TIAO Smart Sprinkler Pi System Connection Diagram.

Make sure all connections are correct, then connect the power wires.

System configuration

The initial configuration includes network configuration, timezone setup and sprinkler station setup.

Network configuration

We have configured the Raspberry Pi image file to use static IP (192.168.1.70) for your Raspberry Pi.

If you plan to use wired connection, just plug a network cable from your home router to Pi, then you are done. You can continue it on the timezone setup section.

If you plan to use an USB wifi adapter, you have two ways to configure the wireless settings for your Pi.

USB wifi adapter supports Access Point (AP) mode

The AP mode means you can use your USB wifi adapter as a router, so you can connect your phone or laptop wirelessly to your Raspberry Pi directly, so that you can setup your Raspberry Pi's wifi using your phone or laptop.

1. Insert a USB wifi adapter which supports to one of the USB ports of your Raspberry Pi. Wait at least 1 minute to allow system to boot up.
2. Use your device (phone/tablet or laptop) to connect to wifi ssid: TSSPi_AP, password is sprinkler.
3. Open Chrome or any browser, use this address: http://192.168.1.70, you will see this:
   
   
   
   
   
   Click on Advanced and select "Proceed to 192.168.1.70":
   
   
   
   
   
   
4. In login page, the default user name is admin, password is admin (You can change this later). Select accept Terms and Conditions, then click Login.
   
   
   
   
   
   
5. You are at the home page of TSSPi. Click on Wifi Setup:
   
   
   
   
   
   
6. At the wifi setup page, click Scan button, then fill in the wifi credentials and click Save button at the top right corner of the screen. We recommend to only modify ssid and password fields.
   
   
   
   
   
   
   
   
   
   
7. You need to reboot your Raspberry Pi in order for it to connect to your home network. Go back to home page by clicking on the Back button at the top of left corner of the screen (do not use browser's back button, or your device's back button, always use Back button from TSSPi), then select Reboot TSSPi:
   
   
   
   
   
   
8. Your TSSPi will reboot in 2 seconds and you will be redirected to login page in 2 minutes. If you have provided corrected ssid and password, TSSPi should connect to your home network after the reboot. Connect your phone or laptop back to your home network, then try to log in, if you can log in, then your wifi configuration is configured successfully. If you have provided wrong information, or TSSPi cannot connect to internet, it will fall back to AP mode, repeat from step 2 and provide correct information.

USB wifi adapter does NOT support Access Point (AP) mode

If your wifi adapter does NOT support AP mode, then you need a network cable to setup the wifi.

Use a network cable to connect the Raspberry Pi to your home router, then follow the above instruction from step 3 to config the wifi. (The device used for config the TSSPi need to connect to the same home network).

Timezone setup

The default timezone is America/New York, if this is not your timezone, you need to config it.

Go to the home page of the TSSPi, select "Setup Time". The page will try to detect your default timezone and pre-select the drop down menu. If your timezone cannot be detected, or the detected timezone is incorrect, select the correct timezone from the drop down menu and tap on Save button:

Change password

The default password for admin is admin. For security reasons, please change the password as soon as possible. Click on "Change Password" button in home page, then follow the instruction to change the password:

Sprinkler steup

In this step, you provide some basic information of your sprinkler system, e.g. total stations, whether the system has a rain sensor or not.

Click "Sprinkler Setup" button on home page to go to sprinkler setup page:

10 PCS, 10cm x 10cm, 2 layers prototype for $38.80 shipped!