Please help 360 usb spi

This site is best viewed in a modern browser with JavaScript enabled.

AndyB@llz

Hello everyone and thank you for taking the time to read this. let me start by saying that i have been doing the jtag hack for some time with the lpt port with no problems. i recently purchased the 360 usb spi the green one not the blue one with the lpt port on it. i have followed all the tutorials and yes i am aware of the mistake on the tutorial with the black wire going on pin 5 when it belongs on pin 6. anyways i am at a standstill i cant even read the nand. in command prompt every time i attempt to read the nand this is what i get
C:\Documents and Settings\XXXXXXXXXXXXXXX>nandpro usb: -r16 nandback.bin
NandPro v2.0d by Tiros
Looking for usb interface device
Could not detect a flash controller!
Can not continue

i would hope that the device that i just purchased is working correctly so i have hopefully just installed something wrong or to the wrong path. and no it is not my solder points on the board. so if anyone could give me some advice it would be greatly appreciated.

TheTwo

AndyB@llz wrote: Hello everyone and thank you for taking the time to read this. let me start by saying that i have been doing the jtag hack for some time with the lpt port with no problems. i recently purchased the 360 usb spi the green one not the blue one with the lpt port on it. i have followed all the tutorials and yes i am aware of the mistake on the tutorial with the black wire going on pin 5 when it belongs on pin 6. anyways i am at a standstill i cant even read the nand. in command prompt every time i attempt to read the nand this is what i get
C:\Documents and Settings\XXXXXXXXXXXXXXX>nandpro usb: -r16 nandback.bin
NandPro v2.0d by Tiros
Looking for usb interface device
Could not detect a flash controller!
Can not continue

i would hope that the device that i just purchased is working correctly so i have hopefully just installed something wrong or to the wrong path. and no it is not my solder points on the board. so if anyone could give me some advice it would be greatly appreciated.

First thing, did you follow the instruction to flash the USB SPI chip first?
tut is here:
http://www.tiaowiki.com/w/How_to_JTAG_XBOX_360_Using_TIAO_USB_SPI_Interface
In device manager, it should look like this before you can dump anything:

thanks

SirReal

I had same problem, I had 2 wires reversed on 360 SPI Board.
SirReal

TheOne

Thanks, yes, it is very easy to mix up the wires

wicked66

i am still getting
looking for usb device
could not detect flash controller
can not continue
i re soldered and re soldered it looks clean and all points are intacti am using the usb spi made by taio from DIYGADGET.COM
does anyone else have this exact product
i plug in the power to xbox dont turn it on then i plug in the usb cable from pc into the usb spi now all wires are just a little longer then my then my middle finger lol whitch is what i want to give to my 360 right jk the usb cable is as long as my arm maybe i should shorten usb cable although it detects it when not pluged into xbox it shows as memory access im going to try to take platic covers off the wires on the end that connects to the usb spi device and see if that works they are kinda loose and slide off easily maybe this is the problem anyone who has this usb spi can help that would be great i also have a xenon board hopefully someone has the same exact setup as me and can help im tearing my hair out lol also when it is plugged in to the pc if i do turn pwer on it works like i have done nothing to it is it true that it should not be able to turn on if it is pluged in to pc via usb spi does that really mean my points are not right? and does my pc have to be a old pc to work ive tryd 2 pc's already oh yeah and i also read something about taio tutorial being wrong something about switching pins 5 and 6 anyone know about this ? taking plastic covers off did not work